curing temperatures造句
例句與造句
typical cure temperatures range from 125 to 175℃. 典型的固化溫度范圍從125175。 - Shrinkage stress was found to increase linearly with cure temperature .
我們發現收縮應力隨固化溫度直線增加。 - Curing temperature and time
養護溫度和時間 - Rate of cure and final strength will depend on the resistance time at the cure temperature
固化比率及最終固化強度取決于在固化溫度條件下所持續的固化時間。 - Influence of curing temperatures on drying shrinkage characteristics of portland cement mortar with high doping of fly ash
養護溫度對高摻量粉煤灰硅酸鹽水泥砂漿干縮性能的影響 - It's difficult to find curing temperatures in a sentence. 用curing temperatures造句挺難的
- The influence of temperature is greater ; the testing is faster and the results is more sensitive at curing temperature 80
溫度對砂漿膨脹影響較大，采用80堿溶液養護，試驗更迅速，結果更敏感。 - Abstract : the influences of curing temperature and alkali contents of cement on expansion of mortar bars are investigated
文摘:研究了養護溫度和水泥堿含量(質量分?jǐn)?shù),下同)與硅質集料砂漿試樣膨脹的關系。 - Results showed that the curing temperature of this system was come down , and the mousiture - resistance of this adhesive was improved
實驗結果表明，采用上述的方法，可以大大降低固化的起始溫度，并對固化后產物的耐濕熱性有一定的提高。 - Final cure temperature below 15 is not recommended for tank linings . if max . recoating interval is exceeded , please consult technical department for instructions
以下的固化溫度不建議用于水箱內層。如果過了最大重涂間隔，施工前請咨詢技術部門。 - Also the infrared ray absorbing properties of the treated fabric can be affected by use of different kind of nano - materials under different curing temperature and concentration
且納米材料的濃度、種類、焙烘溫度都會影響整理織物的紅外線吸收性能。 - The curing of the magnets always in the vacuum circumstance . as far as the mixture cohesion is concerned , the optimized curing temperature and time are 120 and 120min
所用粘結劑合適的固化溫度是120 ，合適的固化時間是120min ，固化后磁體應該隨爐冷卻。 - Both initial curing temperature and final temperature of two systems moved to the peak temperature of the systems with addition of org - mmt , and the peak temperatures were kept constant
加入有機蒙脫土后，兩個固化體系的起始固化溫度和終止固化溫度均明顯向中間靠攏，而峰頂固化溫度基本維持不變。 - 2 . the die cracking with no - flow underfill was analyzed during cooling process from the curing temperature of underfill to the room temperature or to the lowest temperature ( - 55 ) in thermal cycle test
近年來，不流動膠倒裝焊工藝己開始得到應用，但由于不流動膠的固化溫度比常規底充膠高，芯片在冷卻過程中將承受更大的熱應力。 - The results show that : ( 1 ) the cure is accelerated by increasing the usage of cure catalyst and cure temperature , but cure effect is bad with too fast speed , so 3 . 5 % cure catalyst and 80 cure temperature were cheese
研究結果表明： （ 1 ）增加促進劑用量，提高固化溫度對共混物的凝膠速度有明顯的促進作用，但凝膠速度過快會導致低分子物揮發不完全，影響固化效果，通過對比我們選擇的固化條件為：促進劑用量3 . 5 % ，固化溫度為80 。 - The main results are summarized as follows : first , formulation tailoring and curing process of epoxy resin adhesive have been studied , and the peel strengths were tested . the curing temperatures are obtained following the result of curing reaction heat flow tested by dsc
主要研究?jī)?nèi)容和結果如下:首先,研究了作為基底材料基體的環氧樹脂膠粘劑的配方,利用差示掃描量熱儀( dsc )確定了膠粘劑的固化溫度,并對膠粘劑進行了性能測試。
更多例句： 下一頁